Dynomite Diesel 50 Horsepower Injector Set 98.5-02 Dodge 5.9L Cummins
Dynomite's 50 horsepower injectors are notorious for providing a very noticeable increase in power, and typically in MPG's as well, while being extremely clean out the tailpipe. The Dynomite Diesel line of High Flow ISB Injectors for your 98.5-02 Dodge 5.9L Cummins are hailed as the benchmark in 24 valve performance, DDP B series Injectors rule competitions internationally. Whether you want to make big power, or just get your 5th wheel to the camp ground a bit faster, DDP B series Injectors are the answer. These injectors are capable of supporting 375 RWHP with supporting modifications.
In comparison to the stock injectors, your mileage will typically increase 1-2 miles per gallon after your excitement wears off. That makes it pretty hard to pass up these injectors more power and fuel economy!
Please note that some 98.5 trucks will need connector tubes. If your engine serial number is less than 56462598, you will be required to purchase them or your new injectors will not seal properly.
Dynomite Diesel K-Factor Injector Nozzles – Precision. Performance. Power.
When
it comes to injector nozzles, it’s not just about how much fuel you can
dump, it’s about how efficiently you can deliver it. That’s where
Dynomite Diesel’s K-Factor technology sets itself apart from the pack.
Most aftermarket nozzles rely on standard EDM machining, quick, cheap,
and dirty. But Dynomite Diesel isn’t “most.” Instead of stopping at EDM,
they take it further with Advanced Flow Machining (AFM) and precision
honing that smooths out imperfections, polishes internal surfaces, and
radii the inlet of each orifice. The result? Clean, consistent spray
patterns that make more usable power, not just smoke and heat.
Why K-Factor Nozzles Matter:
- Removes Flow Restriction at Orifice Entrance: Eliminates the natural low-pressure zone where fuel enters the orifice, allowing smoother and faster flow.
- Better Fuel Atomization: Fine mist = cleaner burn. That means less black smoke, lower EGTs, and more bang per drop of fuel.
- Delivers More Fuel at Same Pressure: Pushes more volume through a smaller hole, yes, really. It’s about optimized shape, not just size.
- Reduces Turbulence: Smoother internal geometry minimizes swirl and pressure loss inside the nozzle, no flow drama here.
- Improved Power and Efficiency: With better atomization comes better combustion, and that means more horsepower, cooler temps, and increased fuel mileage.
- Less Smoke, More Go: Bigger isn’t always better, smoky, hot tunes waste fuel. K-Factor nozzles strike the perfect balance for performance builds and daily drivers alike.
Dynomite starts with blank nozzles or custom machined pieces based on specific spray angle requirements. Each nozzle goes through a proprietary honing process, no shortcuts. The end result? A nozzle that not only flows more but does so smarter, delivering cleaner, cooler, more efficient power than the competition. Whether you're building a mild street truck or an all-out track monster, K-Factor Nozzles give you the edge where it counts, in real world performance.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Dynomite Diesel 50 Horsepower Injector Set 98.5-02 Dodge 5.9L Cummins
Dynomite Diesel 50 Horsepower Injector Set 98.5-02 Dodge 5.9L Cummins
Dynomite's 50 horsepower injectors are notorious for providing a very noticeable increase in power, and typically in MPG's as well, while being extremely clean out the tailpipe. The Dynomite Diesel line of High Flow ISB Injectors for your 98.5-02 Dodge 5.9L Cummins are hailed as the benchmark in 24 valve performance, DDP B series Injectors rule competitions internationally. Whether you want to make big power, or just get your 5th wheel to the camp ground a bit faster, DDP B series Injectors are the answer. These injectors are capable of supporting 375 RWHP with supporting modifications.
In comparison to the stock injectors, your mileage will typically increase 1-2 miles per gallon after your excitement wears off. That makes it pretty hard to pass up these injectors more power and fuel economy!
Please note that some 98.5 trucks will need connector tubes. If your engine serial number is less than 56462598, you will be required to purchase them or your new injectors will not seal properly.
Dynomite Diesel K-Factor Injector Nozzles – Precision. Performance. Power.
When
it comes to injector nozzles, it’s not just about how much fuel you can
dump, it’s about how efficiently you can deliver it. That’s where
Dynomite Diesel’s K-Factor technology sets itself apart from the pack.
Most aftermarket nozzles rely on standard EDM machining, quick, cheap,
and dirty. But Dynomite Diesel isn’t “most.” Instead of stopping at EDM,
they take it further with Advanced Flow Machining (AFM) and precision
honing that smooths out imperfections, polishes internal surfaces, and
radii the inlet of each orifice. The result? Clean, consistent spray
patterns that make more usable power, not just smoke and heat.
Why K-Factor Nozzles Matter:
- Removes Flow Restriction at Orifice Entrance: Eliminates the natural low-pressure zone where fuel enters the orifice, allowing smoother and faster flow.
- Better Fuel Atomization: Fine mist = cleaner burn. That means less black smoke, lower EGTs, and more bang per drop of fuel.
- Delivers More Fuel at Same Pressure: Pushes more volume through a smaller hole, yes, really. It’s about optimized shape, not just size.
- Reduces Turbulence: Smoother internal geometry minimizes swirl and pressure loss inside the nozzle, no flow drama here.
- Improved Power and Efficiency: With better atomization comes better combustion, and that means more horsepower, cooler temps, and increased fuel mileage.
- Less Smoke, More Go: Bigger isn’t always better, smoky, hot tunes waste fuel. K-Factor nozzles strike the perfect balance for performance builds and daily drivers alike.
Dynomite starts with blank nozzles or custom machined pieces based on specific spray angle requirements. Each nozzle goes through a proprietary honing process, no shortcuts. The end result? A nozzle that not only flows more but does so smarter, delivering cleaner, cooler, more efficient power than the competition. Whether you're building a mild street truck or an all-out track monster, K-Factor Nozzles give you the edge where it counts, in real world performance.
Original: $783.75
-70%$783.75
$235.12Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Dynomite's 50 horsepower injectors are notorious for providing a very noticeable increase in power, and typically in MPG's as well, while being extremely clean out the tailpipe. The Dynomite Diesel line of High Flow ISB Injectors for your 98.5-02 Dodge 5.9L Cummins are hailed as the benchmark in 24 valve performance, DDP B series Injectors rule competitions internationally. Whether you want to make big power, or just get your 5th wheel to the camp ground a bit faster, DDP B series Injectors are the answer. These injectors are capable of supporting 375 RWHP with supporting modifications.
In comparison to the stock injectors, your mileage will typically increase 1-2 miles per gallon after your excitement wears off. That makes it pretty hard to pass up these injectors more power and fuel economy!
Please note that some 98.5 trucks will need connector tubes. If your engine serial number is less than 56462598, you will be required to purchase them or your new injectors will not seal properly.
Dynomite Diesel K-Factor Injector Nozzles – Precision. Performance. Power.
When
it comes to injector nozzles, it’s not just about how much fuel you can
dump, it’s about how efficiently you can deliver it. That’s where
Dynomite Diesel’s K-Factor technology sets itself apart from the pack.
Most aftermarket nozzles rely on standard EDM machining, quick, cheap,
and dirty. But Dynomite Diesel isn’t “most.” Instead of stopping at EDM,
they take it further with Advanced Flow Machining (AFM) and precision
honing that smooths out imperfections, polishes internal surfaces, and
radii the inlet of each orifice. The result? Clean, consistent spray
patterns that make more usable power, not just smoke and heat.
Why K-Factor Nozzles Matter:
- Removes Flow Restriction at Orifice Entrance: Eliminates the natural low-pressure zone where fuel enters the orifice, allowing smoother and faster flow.
- Better Fuel Atomization: Fine mist = cleaner burn. That means less black smoke, lower EGTs, and more bang per drop of fuel.
- Delivers More Fuel at Same Pressure: Pushes more volume through a smaller hole, yes, really. It’s about optimized shape, not just size.
- Reduces Turbulence: Smoother internal geometry minimizes swirl and pressure loss inside the nozzle, no flow drama here.
- Improved Power and Efficiency: With better atomization comes better combustion, and that means more horsepower, cooler temps, and increased fuel mileage.
- Less Smoke, More Go: Bigger isn’t always better, smoky, hot tunes waste fuel. K-Factor nozzles strike the perfect balance for performance builds and daily drivers alike.
Dynomite starts with blank nozzles or custom machined pieces based on specific spray angle requirements. Each nozzle goes through a proprietary honing process, no shortcuts. The end result? A nozzle that not only flows more but does so smarter, delivering cleaner, cooler, more efficient power than the competition. Whether you're building a mild street truck or an all-out track monster, K-Factor Nozzles give you the edge where it counts, in real world performance.
